احتیاط برای نصب از سمی و مضر گاز اشکارسازها
سمی گاز زنگ هشدار تشکیل شده از اشکارساز و زنگ هشدار کنترل میزبان٪ 2c به طور گسترده ای استفاده می شود در پتروشیمی صنعت که در ان سمی گازها وجود دارد٪ 2c مانند نفت٪ 2c گاز ٪ 2c شیمیایی ٪ 2c و نفت انبارها. این استفاده می شود استفاده می شود برای شناسایی نشت در داخلی و در فضای باز خطرناک مناطق و مهم ابزار برای اطمینان تولید و شخصی ایمنی. هنگامی که وجود دارد سمی گاز در ازمایش شده سایت ٪ 2c اشکارساز تبدیل گاز سیگنال به ولتاژ سیگنال یا جریان سیگنال و انتقال ان به زنگ ابزار. ابزار نمایش درصد غلظت مقدار از در حالی که در حال حاضر در حال حاضر در حالی که در حال حاضر در حال حاضر در حالی که بدون وجود دارد که در حال حاضر در حالی که در حال حاضر در حالی که بدون وجود دارد که در حالی که در حال حاضر در حالی که در حال حاضر در حالی که بدون وجود دارد که در حالی که در حال حاضر در حالی که بدون وجود دارد که در حالی که در حال حاضر در حالی کهبه موقع روش برای جلوگیری از احتراق و انفجار حوادث.
٪0a1. اقدامات احتیاطی در طول کاربرد
هنگامی که ثابت نصب از سمی گاز زنگ هشدار است در محل٪ 2c ان موقعیت است نه به راحتی تغییر کرده است. زیر نقاط باید در نظر گرفته شود هنگامی که ان به طور خاص اعمال می شود.
٪0a(1) شناسایی پتانسیل نشت نقاط از دستگاه به be monitored٪2c analyze their leakage pressure٪2c direction٪2c and other factors٪2c and other factors٪2c and draw a distribution map of probe positions. According to the the severity of the leakage٪2c it is divided into three levels٪3a I٪2c II٪2c and III.
٪0a(2) تعیین جهت از سمی گاز نشت هنگامی که a large amount of leakage occurs based on specific factors such as airflow direction and wind direction in the location.
٪0a(3) According to the density of leaking gas (greater than or less than air)٪2c combined with the air flow trend٪2c the the three-dimensional flow Run chart of leakage is synthesized٪2c and the the initial point setting scheme is made at the the downstream of the the flow.
(4) Study whether the leakage state of the leakage point is micro leakage or jet like. If it is a slight leak, the location of the point should be closer to the leak point. If it is a jet leakage, it should be slightly away from the leakage point. Based on these conditions, a final site setting plan has been formulated. In this way, the quantity and variety to be purchased can be estimated.
٪ 0a (5) برای مکان ها با قابل توجه سمی گاز نشت ٪ 2c a تشخیص نقطه باید تنظیم شود تا هر ٪ 7b ٪ 7b1 ٪ 7d٪ 7dm جدا مطابق مرتبط مقررات برای کوچک وی در ادامه می دهد: با وجود اینکه در سال های 14،44 به عنوان اولین بار در جهان با وجود دارد که در ادامه می دهد: با وجود اینکه در ادامه می 14 با وجود وجود دارد که در ادامه می 14
٪0a(6) For places with hydrogen leakage٪2c the detector should be installed on the plane above the the leakage point.
٪ 0a (7) برای رسانه با a گاز تراکم بیشتر از هوا٪ 2c اشکارساز باید نصب شود در a هواپیما زیر نشت نقطه ٪ 2c و توجه باید پرداخت شود به ویژگی های از محیط اطراف برای مکان ها مستعد به تجمع از سمی گازها٪ 2c ویژه توجه باید پرداخت شود به تنظیم از نظارت نقاط.
(8) For open toxic gas diffusion and escape environments, if there is a lack of good ventilation conditions, it is easy to make the toxic gas content in the air of a certain location close to or reach the lower explosive limit concentration. These are monitoring points that cannot be ignored. According to the analysis of on-site accidents, more than half of them were caused by incorrect installation and calibration. Therefore, it is necessary to introduce the precautions for correct installation and calibration to reduce malfunctions.
2. Precautions for the installation of toxic gas alarms
(1) The alarm probe is mainly a detection element that contacts the combustion gas sensor. It consists of a spherical platinum wire coil wrapped with aluminum oxide and Adhesive. Its outer surface is covered with platinum, palladium and other rare metals. Therefore, be careful during installation to avoid damaging the probe.
٪ 0a (2) نصب ارتفاع از زنگ هشدار باید به طور کلی بین ٪ 7b٪ 7b1٪ 7d٪ 7dcm به تسهیل روزانه تعمیر و نگهداری توسط تعمیر و نگهداری پرسنل.
٪ 0a (3) زنگ است اندازه گیری ابزار با صدا و نور نمایش توابع٪ 2c و باید نصب شود در a محل جایی که کارگران می توانند به راحتی دیدن و شنیدن ان ٪ 2c در به منظور حذف پنهان خطرات در a به موقع شیوه.
(4) There should be no strong electromagnetic fields (such as high-power motors and transformers) around the alarm that may affect the operation of the instrument.
(5) The installation position of indoor probes should also vary depending on the density of the measured gas. When the measured gas density is less than the Density of air, the probe shall be installed 30cm away from the roof in a downward direction; On the contrary, the probe should be installed 30cm above the ground in an upward direction.
